Source: This Old House flat roof replacement cost guide (updated March 16, 2026), for a 2,000 sq ft roof with builder-grade materials. National figures, not Bluebonnet prices.
The main commercial roofing types are single-ply membranes (TPO, PVC and EPDM), modified bitumen, built-up "tar and gravel" roofs, spray foam and roof coatings, and metal. Most of them are built for low-slope roofs, the flat or gently sloping roofs on retail centers, offices, warehouses and churches. Which one fits a building depends on how the roof drains, how much foot traffic and equipment it carries, the budget and how long the owner plans to hold the property.
This guide walks through each type in plain terms, compares them side by side, and covers what matters for buildings in the North Texas heat and hail. If you need someone to look at a roof now, our commercial roofing page explains how we inspect and price one.
What's in this guide
- Low-slope vs steep-slope commercial roofs
- Single-ply membranes: TPO, PVC and EPDM
- Modified bitumen and built-up roofs
- Spray foam and roof coatings
- Metal roofs on commercial buildings
- Commercial roofing types compared
- Choosing a roof for a North Texas building
- How we inspect and price a commercial roof
- Common questions
Low-slope vs steep-slope commercial roofs
The first split is the pitch of the roof. The EPA describes low-slope roofs as the flat or gently sloping roofs typically found on commercial, industrial and office buildings, and steep-slope roofs as the ones used on houses. This Old House defines a flat roof as one that slopes 10 degrees or less.
A low-slope roof cannot rely on gravity to shed water quickly, so it needs a continuous waterproof layer rather than overlapping pieces. That is why commercial roofing is mostly sheets and liquids: membranes rolled out in wide runs, layered asphalt systems, foam sprayed on in place and coatings rolled over the top. Some commercial buildings, such as small offices, churches and restaurants with a pitched roof, use the same shingle, tile or metal you would see on a house.
Single-ply membranes: TPO, PVC and EPDM
Most low-slope commercial roofs today are a single-ply membrane laid in wide sheets over insulation board. The EPA describes single-ply membranes as prefabricated sheets rolled onto the roof. There are three main kinds:
- TPO (thermoplastic polyolefin). A white membrane with seams heat-welded into one continuous sheet. This Old House notes it is common on strip malls and warehouses because it repels dirt and reflects UV light.
- PVC. Also a white, heat-welded membrane. It looks much like TPO from the ground but is a different plastic with its own properties.
- EPDM. A synthetic rubber membrane, usually black, with seams joined by tape or adhesive. This Old House says it expands and contracts through weather extremes without cracking, and that white rubber suits hot climates better than black.
The welded seams on TPO and PVC are a big part of their appeal, because seams are where many flat roofs start to leak. The white surface also matters in Texas, which the section on heat below covers.
Modified bitumen and built-up roofs
Modified bitumen is asphalt blended with polymers and made into rolled sheets, usually installed in more than one layer over a base sheet. This Old House lists it as the most affordable flat roofing option and says it resists cracking through temperature swings.
Built-up roofing, often called tar and gravel, is the oldest of the low-slope systems. It is built from several alternating layers of felt and hot asphalt, often topped with gravel. This Old House says the extra layers help seal small punctures before they turn into leaks, which helps on roofs with branches or maintenance traffic. Both systems are heavier than a single-ply membrane, which matters if a new roof is going on over an old one.
Spray foam and roof coatings
Spray polyurethane foam goes on as a liquid and expands into a solid layer that seals around penetrations and edges. It is finished with a protective coating, which is what takes the sun and needs renewing over time.
A roof coating on its own is a different job: a liquid membrane rolled or sprayed over an existing roof that is still sound underneath. The EPA lists liquid-applied coatings in light or cool colors among its low-slope cool roof products. A coating can buy years on a roof with good insulation and a dry deck, but it cannot fix wet insulation or a failed deck under it. Whether a coating is worth doing depends on what is under it.
Metal roofs on commercial buildings
Metal shows up on commercial buildings in two ways. Ribbed screw-down panels are common on shops, barns and metal buildings, and standing seam panels, with raised seams and hidden clips, are used on offices, churches and retail buildings with enough slope. This Old House gives metal the longest expected life of the flat roof options, 40 to 100 years, and the highest price, $15 to $21 per square foot. Our metal roof cost guide covers the panel styles in more detail.
Commercial roofing types compared
| Type | What it is | Cost per sq ft |
|---|---|---|
| Modified bitumen | Polymer-modified asphalt sheets, usually multi-layer | $7 to $9 |
| Built-up (tar and gravel) | Alternating felt and asphalt layers, often with gravel | $7 to $9 |
| TPO | White single-ply membrane, heat-welded seams | $8 to $11 |
| EPDM | Rubber single-ply membrane, taped or glued seams | $9 to $13 |
| Metal | Screw-down or standing seam panels | $15 to $21 |
| Spray foam / coating | Liquid-applied layer, finished with a coating | Depends on the roof under it |
Source: This Old House, "How Much Does a Flat Roof Replacement Cost?" (updated March 16, 2026), Homewyse figures for a 2,000 sq ft roof. Large commercial roofs are priced on their own scope: insulation, tear-off, drains and rooftop equipment change the total far more than the membrane choice.
PVC is not broken out in that guide. Treat these as a sense of how the systems rank on price, not as a budget for a commercial building.
Choosing a roof for a North Texas building
Heat and reflectance
A dark roof in a Texas summer absorbs a lot of heat, and the building pays for it in air conditioning. The EPA says cool roofs absorb and transfer less of the sun's heat into the building, and that buildings with cool roofs use less air conditioning.
The Cool Roof Rating Council, which tests and rates roofing products, measures solar reflectance and thermal emittance both new and after three years outdoors, and publishes the results in its Rated Roof Products Directory. White TPO and PVC and light coatings are the usual cool choices. The EPA also notes that low-slope cool roofs may need periodic cleaning to keep their reflectance.
Hail
Hail can bruise or puncture a membrane, crack an aging coating and dent rooftop units and metal panels. The Texas Department of Insurance says impact-tested roofing, including sheets and formed metal panels, is rated Class 1 to 4, with insurers setting their own credits (TDI roofing discounts, as of February 24, 2023). Ask your carrier what it recognizes before you choose.
Drainage, traffic and equipment
Low-slope roofs live or die by how they shed water. Standing water after a rain speeds up wear, so drains, scuppers and tapered insulation are part of the decision, not an afterthought. Roofs with HVAC units, kitchen exhaust or frequent service visits need a surface and walk pads that tolerate foot traffic. Those details often decide the type more than the brochure does.
How we inspect and price a commercial roof
Bluebonnet Construction & Roofing works on low-slope roofs for owners, property managers and general contractors, from repairs to full replacements. Our focus is white single-ply membrane, and we work with TPO, PVC and EPDM. Owner Cody Taylor inspects the roof and writes the estimate himself. He walks the whole field, the edges and parapets, every drain and rooftop unit, and notes where water stands after rain.
Not every commercial leak means a new roof. If a repair will hold, we say so and price the repair, and we tell you plainly whether a coating, foam or a new membrane is the right call. The inspection is free, and the written estimate comes by email so you can forward it to an owner, a board or a partner.
We work on commercial buildings in Fort Worth, Arlington, Weatherford, Burleson and Aledo. To schedule a free inspection, start from our commercial roofing page.
FAQ
What type of roofs are on commercial buildings?
Most commercial buildings have a low-slope roof covered with a single-ply membrane (TPO, PVC or EPDM), modified bitumen, a built-up tar and gravel roof, or spray foam with a coating. Metal panels are common on shops and metal buildings, and some smaller commercial buildings with pitched roofs use shingle, tile or metal like a house.
What is considered commercial roofing?
Commercial roofing is roofing on business, industrial and institutional buildings such as retail centers, offices, warehouses and churches. Most of it is low-slope roofing, where a continuous membrane or liquid-applied layer keeps the water out instead of overlapping shingles.
What is the most common commercial roof type?
On low-slope buildings today, single-ply membranes are the usual choice, with white TPO very common on strip malls and warehouses. Older buildings often still have modified bitumen or built-up roofs.
What is the difference between TPO and EPDM?
TPO is a white thermoplastic membrane whose seams are heat-welded into one sheet. EPDM is a synthetic rubber membrane, usually black, whose seams are joined with tape or adhesive. This Old House puts TPO at $8 to $11 and EPDM at $9 to $13 per square foot on a 2,000 sq ft flat roof.
Can a commercial roof be coated instead of replaced?
Sometimes. A coating is a liquid membrane applied over an existing roof that is still sound underneath. It will not fix wet insulation or a damaged deck, so the roof needs an inspection first to see whether a coating, a repair or a new membrane is the right call.
How long does a commercial flat roof last?
This Old House says flat roofs typically last 15 to 20 years depending on the material, with modified bitumen and built-up roofs lasting 10 to 20 years and metal 40 to 100 years. Drainage, foot traffic and maintenance change those numbers on a real building.